Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

Got a problem with my 1999 Mazda B2500 (Ford Ranger under the hood), and
before I take it to my "plug it into the computer, no error codes, nothing's
wrong with it" mechanic, I wanted to run it by some people that know a
little more about vehicles. Here's the basics of my truck & the problem

1999 Mazda B2500
4-cylinder engine
5-speed manual transmission
130,000 miles +/-, original everything (including clutch)
2-wheel / rear wheel drive

Problem: vehicle makes a metallic chattering sound (like someone with steel
dentures chattering their teeth in the cold, best way I can describe it, or
maybe like a dime rattling around in an empty beer can) intermittently.
Sound seems to be coming from under the floor boards, close to the back end
of the vehicle. Sound is worst when there is a load on the engine,
especially in higher gears & when going up hill, or if I let the clutch out
too slow when up shifting to a higher gear. Sound only happened once when
there was no load on the engine. Engine sounds are normal, engine idles
within normal parameters (500-750rpms), accelerates well both on flats and
up hill. No idiot lights have come up on my panels (and this truck is like
a nervous child, if it thinks even the slightest thing MAY be wrong, my dash
lights up like a Christmas tree). Sound happens more often at lower RPMs
(just before I down shift) or when accelerating suddenly.

I had chalked it up to an old vehicle with a loose panel or something else
that's pointless to worry about, until today when a friend (and former
mechanic) said it may be something in the driveshaft and/or rear
differential. At first I thought the worst this could be was that my
130,000 mile clutch is finally giving out on me, even though it feels ok.
When he mentioned this, I had nightmare images of a bearing seizing up and
my transmission blowing out as a result.

Obviously to diagnose a problem, it helps to be IN the vehicle, but anybody
want to shed some light on the above? Feel free to ask for more info. I'm
just trying to get some feedback & suggestions before I take Chicken
Little's advice about the sky (and my driveshaft) falling.

C.

Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

From your description, it sounds like a loose or damaged exhaust heat
shield.


On 4/4/07 5:39 PM, in article ,
"Chicken-Fried Steak" > wrote:

> Got a problem with my 1999 Mazda B2500 (Ford Ranger under the hood), and
> before I take it to my "plug it into the computer, no error codes, nothing's
> wrong with it" mechanic, I wanted to run it by some people that know a
> little more about vehicles. Here's the basics of my truck & the problem
>
> 1999 Mazda B2500
> 4-cylinder engine
> 5-speed manual transmission
> 130,000 miles +/-, original everything (including clutch)
> 2-wheel / rear wheel drive
>
> Problem: vehicle makes a metallic chattering sound (like someone with steel
> dentures chattering their teeth in the cold, best way I can describe it, or
> maybe like a dime rattling around in an empty beer can) intermittently.
> Sound seems to be coming from under the floor boards, close to the back end
> of the vehicle. Sound is worst when there is a load on the engine,
> especially in higher gears & when going up hill, or if I let the clutch out
> too slow when up shifting to a higher gear. Sound only happened once when
> there was no load on the engine. Engine sounds are normal, engine idles
> within normal parameters (500-750rpms), accelerates well both on flats and
> up hill. No idiot lights have come up on my panels (and this truck is like
> a nervous child, if it thinks even the slightest thing MAY be wrong, my dash
> lights up like a Christmas tree). Sound happens more often at lower RPMs
> (just before I down shift) or when accelerating suddenly.
>
> I had chalked it up to an old vehicle with a loose panel or something else
> that's pointless to worry about, until today when a friend (and former
> mechanic) said it may be something in the driveshaft and/or rear
> differential. At first I thought the worst this could be was that my
> 130,000 mile clutch is finally giving out on me, even though it feels ok.
> When he mentioned this, I had nightmare images of a bearing seizing up and
> my transmission blowing out as a result.
>
> Obviously to diagnose a problem, it helps to be IN the vehicle, but anybody
> want to shed some light on the above? Feel free to ask for more info. I'm
> just trying to get some feedback & suggestions before I take Chicken
> Little's advice about the sky (and my driveshaft) falling.
>
> C.
>
>

Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

"Chicken-Fried Steak" > wrote in message
...
> Got a problem with my 1999 Mazda B2500 (Ford Ranger under the hood), and
> before I take it to my "plug it into the computer, no error codes,
> nothing's wrong with it" mechanic, I wanted to run it by some people that
> know a little more about vehicles. Here's the basics of my truck & the
> problem
>
> 1999 Mazda B2500
> 4-cylinder engine
> 5-speed manual transmission
> 130,000 miles +/-, original everything (including clutch)
> 2-wheel / rear wheel drive
>
> Problem: vehicle makes a metallic chattering sound (like someone with
> steel dentures chattering their teeth in the cold, best way I can describe
> it, or maybe like a dime rattling around in an empty beer can)
> intermittently. Sound seems to be coming from under the floor boards,
> close to the back end of the vehicle. Sound is worst when there is a load
> on the engine, especially in higher gears & when going up hill, or if I
> let the clutch out too slow when up shifting to a higher gear. Sound only
> happened once when there was no load on the engine. Engine sounds are
> normal, engine idles within normal parameters (500-750rpms), accelerates
> well both on flats and up hill. No idiot lights have come up on my panels
> (and this truck is like a nervous child, if it thinks even the slightest
> thing MAY be wrong, my dash lights up like a Christmas tree). Sound
> happens more often at lower RPMs (just before I down shift) or when
> accelerating suddenly.
>
> I had chalked it up to an old vehicle with a loose panel or something else
> that's pointless to worry about, until today when a friend (and former
> mechanic) said it may be something in the driveshaft and/or rear
> differential. At first I thought the worst this could be was that my
> 130,000 mile clutch is finally giving out on me, even though it feels ok.
> When he mentioned this, I had nightmare images of a bearing seizing up and
> my transmission blowing out as a result.
>
> Obviously to diagnose a problem, it helps to be IN the vehicle, but
> anybody want to shed some light on the above? Feel free to ask for more
> info. I'm just trying to get some feedback & suggestions before I take
> Chicken Little's advice about the sky (and my driveshaft) falling.
>
> C.

From your description of the noise it sounds like you may have a bad
u-joint. Put the trans in neutral, apply the parking brake and crawl under
the truck to inspect the u-joints. Check for slop in the u-joints but also
check for rust were the u-joint cross goes into the bearing caps. If you
find either condition replace the u-joints. I am thinking you will find they
are rusty and that is causing your noise.

Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

Chicken-Fried Steak > wrote:
>
>I had chalked it up to an old vehicle with a loose panel or something else
>that's pointless to worry about, until today when a friend (and former
>mechanic) said it may be something in the driveshaft and/or rear
>differential. At first I thought the worst this could be was that my
>130,000 mile clutch is finally giving out on me, even though it feels ok.
>When he mentioned this, I had nightmare images of a bearing seizing up and
>my transmission blowing out as a result.

I agree, it sounds like it is in the driveshaft or differential.

>Obviously to diagnose a problem, it helps to be IN the vehicle, but anybody
>want to shed some light on the above? Feel free to ask for more info. I'm
>just trying to get some feedback & suggestions before I take Chicken
>Little's advice about the sky (and my driveshaft) falling.

First thing, jack the car up. Grab the driveshaft and push it forward
and back, then right to left. Do you feel any play in it? Do the same
for the axles.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

On Wed, 4 Apr 2007 18:39:11 -0400, "Chicken-Fried Steak"
> wrote:

>Got a problem with my 1999 Mazda B2500 (Ford Ranger under the hood), and
>before I take it to my "plug it into the computer, no error codes, nothing's
>wrong with it" mechanic, I wanted to run it by some people that know a
>little more about vehicles. Here's the basics of my truck & the problem
>
>1999 Mazda B2500
>4-cylinder engine
>5-speed manual transmission
>130,000 miles +/-, original everything (including clutch)
>2-wheel / rear wheel drive
>
>Problem: vehicle makes a metallic chattering sound (like someone with steel
>dentures chattering their teeth in the cold, best way I can describe it, or
>maybe like a dime rattling around in an empty beer can) intermittently.
>Sound seems to be coming from under the floor boards, close to the back end
>of the vehicle. Sound is worst when there is a load on the engine,

The heat shield is loose on your Cat converter or the converter core
has melted. Most likely the heat shield.
>especially in higher gears & when going up hill, or if I let the clutch out
>too slow when up shifting to a higher gear. Sound only happened once when
>there was no load on the engine. Engine sounds are normal, engine idles
>within normal parameters (500-750rpms), accelerates well both on flats and
>up hill. No idiot lights have come up on my panels (and this truck is like
>a nervous child, if it thinks even the slightest thing MAY be wrong, my dash
>lights up like a Christmas tree). Sound happens more often at lower RPMs
>(just before I down shift) or when accelerating suddenly.
>
>I had chalked it up to an old vehicle with a loose panel or something else
>that's pointless to worry about, until today when a friend (and former
>mechanic) said it may be something in the driveshaft and/or rear
>differential. At first I thought the worst this could be was that my
>130,000 mile clutch is finally giving out on me, even though it feels ok.
>When he mentioned this, I had nightmare images of a bearing seizing up and
>my transmission blowing out as a result.
>
>Obviously to diagnose a problem, it helps to be IN the vehicle, but anybody
>want to shed some light on the above? Feel free to ask for more info. I'm
>just trying to get some feedback & suggestions before I take Chicken
>Little's advice about the sky (and my driveshaft) falling.
>
>C.
>


--
Posted via a free Usenet account from http://www.teranews.com

Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

"E Meyer" > wrote in message
...
> From your description, it sounds like a loose or damaged exhaust heat
> shield.
>
>
> On 4/4/07 5:39 PM, in article
> ,
> "Chicken-Fried Steak" > wrote:
>
>> Got a problem with my 1999 Mazda B2500 (Ford Ranger under the hood), and
>> before I take it to my "plug it into the computer, no error codes,
>> nothing's
>> wrong with it" mechanic, I wanted to run it by some people that know a
>> little more about vehicles. Here's the basics of my truck & the problem
>>
>> 1999 Mazda B2500
>> 4-cylinder engine
>> 5-speed manual transmission
>> 130,000 miles +/-, original everything (including clutch)
>> 2-wheel / rear wheel drive
>>
>> Problem: vehicle makes a metallic chattering sound (like someone with
>> steel
>> dentures chattering their teeth in the cold, best way I can describe it,
>> or
>> maybe like a dime rattling around in an empty beer can) intermittently.
>> Sound seems to be coming from under the floor boards, close to the back
>> end
>> of the vehicle. Sound is worst when there is a load on the engine,
>> especially in higher gears & when going up hill, or if I let the clutch
>> out
>> too slow when up shifting to a higher gear. Sound only happened once
>> when
>> there was no load on the engine. Engine sounds are normal, engine idles
>> within normal parameters (500-750rpms), accelerates well both on flats
>> and
>> up hill. No idiot lights have come up on my panels (and this truck is
>> like
>> a nervous child, if it thinks even the slightest thing MAY be wrong, my
>> dash
>> lights up like a Christmas tree). Sound happens more often at lower RPMs
>> (just before I down shift) or when accelerating suddenly.
>>
>> I had chalked it up to an old vehicle with a loose panel or something
>> else
>> that's pointless to worry about, until today when a friend (and former
>> mechanic) said it may be something in the driveshaft and/or rear
>> differential. At first I thought the worst this could be was that my
>> 130,000 mile clutch is finally giving out on me, even though it feels ok.
>> When he mentioned this, I had nightmare images of a bearing seizing up
>> and
>> my transmission blowing out as a result.
>>
>> Obviously to diagnose a problem, it helps to be IN the vehicle, but
>> anybody
>> want to shed some light on the above? Feel free to ask for more info.
>> I'm
>> just trying to get some feedback & suggestions before I take Chicken
>> Little's advice about the sky (and my driveshaft) falling.
>>
>> C.
>>
>>
>

I had the same sound on my '91 Ranger 4x4 until the heat shield fell off in
an intersection. Solved the sound problem! ;-)

Metallic chattering sound - Mazda B2500 (Ford Ranger)
 

Mine is doing the exact same thing. Same truck as well except mine has 284k.. PREV owner did not love her and she sat for a long time prior to 6 months ago when I got her. Replaced all wheel bearings and both calipers on front.. Rotate tires and filled tc. She was low so I drained and refilled but fluid was black. Couldnt tell if there was metallic shavings due to the pan I was handed. I wasnt aware there was **** already in the bottom of the pan before I used it. She doesnt drag as bad now when coasting that's for sure. Ps res is full. Black, but full. Shes old and prob never went under the knife in years. Clutch n brake res are full. Flushed brake system as well. Clutch feels fine surprisingly. But I can sometimes hear the "denture" sound in drivethrus where sound echoes if I pump the clutch without shifting. When I first test drove her I assumed rear diff was low on fluid. When I got her I check it through vent hose and she wasnt low enough for the amount of lip I'm getting from her if ya know what I'm saying.