1) What is the current wisdom on dealing with carb, fuel pump, master cylinder, etc. after long sit? Should items with gaskets, seals, etc. be replaced or kitted if available? 2) Should I consider replacing the rubber cushions in the frame and body mounts if they appear to be intact, or should I...

I'm getting ready to install a new exhaust system w/mufflers on my 63 SB that I bought from Zip- 14-gauge aluminized tubing (.070 wall). Has anyone used a paint on this type of exhaust for a rust inhibitor? If yes, what brand and did they have a good long-term result. I have the paint for the...

I have the original radio in my 63 accessible at this time. The radio worked fine on AM + FM when parked it many years ago. I had a selfmade, portable, low-tech cassette system w/2speakers that I removed from the car when not using. Is there current technology using a portable MP3 type music...

How do I determine the gear ratio in my 63 250hp 4spd- are there #'s on the housing or 3rd member? It don't believe it has posi-track. Thanx- lib

Is there a way to replace the rear to front metal brake line in one piece w/out removing body? I bought a new line from Zip but can't seem to find a way to install it intact. It appears that perhaps it could be cut and re-coupled to make it install. My concern is it has been stored for 20+ and...

I need to replace both cables on my 63 SB/ no AC. What is the correct gauge of wire to construct the cables? Thanx- lib

I need to replace the existing cap on my tank.The existing is an old pressure-relief lever type that has deteriorated. I looked at Zip, CC, etc. and they want an original style replacement (#307) cap for $35 approx. I am not re-storing the car for show, it's a driver, and it seems to me if I...

What Goodyear model would be a good, smooth, soft-riding tire size for a 250HP roadster? I am interested in a road, not race tire. The entire suspension has been replaced and I will need to have both front and back aligned. The alignment shop recommended that I install the new tires before...

I would like to purchase new hardware for the above 15' X 6.5" set of 4. The rims cleaned-up well but the nuts+washers had some deep rust. The car is nearly finished, w/new Goodyears, and looking good so would like to replace the rusted pieces. Any clues on who I might contact to purchase these...

I recently over-hauled my 63 SB and had the heads modified to run un-leaded gas. Will ehtnol work with the current valve/ carb. configs or will it necessitate another mod.

I need the front bearing retainer for my Borg Warner 4spd. It is the part on the front of the trans. that the throw-out bearing rides on. Zip, Corv. Central, Ecker, etc. on carry parts for the Muncie M22 that they put in the 63 late on thru 1974. Any leads on where I might order this part...

What is the current wisdom on the prefered placement of an ignition kill switch in the electrical system. Is it better to kill one side of the coil, or starter, etc. to prevent an easy hot wire of the ignition switch. Obviously, the switch itself will be secreted. Thanx- Lib

How do I know if my roadster is an "early" or "late" build? I want to buy a correct fuel lid+bezel for it. Any recommendations for parts outlet also?

1) I am going to get the deluxe rebuild kits for the front & rear suspension.Are the poly bushings a better product than the rubber ones? 2) Are the stainless brake lines better than the steel/tin lines in regards to longevity? 3) Any opinions or experience with this exhaust system at Ebay; Item...

The motor is the correct block+heads. However, the machine shop maestro, who is a real Chevy guru , informed me that the valve covers are not correct. Any recommendations on where to purchase an affordable, correct set?

I want to put on new shocks that don't give a stiff ride, but also don't let it yaw over in the corners. The springs look good, (the front have a couple of rubber spacers in them) but I don't know what would help me decide to replace the springs. They are not an expensive item, but to just put...

I am going to re-build the suspension in my roadster. I've looked at numerous kits and I think the kit at http://stores.ebay.com/Willcox-Wholesale-Corvette-Parts_W0QQssPageNameZVIStoreHeaderLinksQQtZkm (part #58-33AK 63-64) is the one I am going to get. I noticed that my rear trailing arms have...

I've been able to decode my 1963 roadster's VIN upto the S (St.Louis). The remaining numbers are 114229. Would someone with the magic decoder book (or a link to that info) please tell me what date those numbers represent? I've looked on line with no luck so far for the last 6 digits. Thanx- Lib

1) I am going to replace my clutch with a basic stock type kit. I've looked at Ecklers, Zip, etc. and they all are comprable in price and none list the manufacturer of the parts. My local parts supplier offered me a Borg -Warner kit for approx. $40 less and no shipping. How can I compare what the...

I see that the correct mirror ( longbase)is specific to my 63E. Does the interior door panel need to be removed to install a mirror correctly or is it done externally? The driver side has been replaced with a generic mirror.I am considering replacing it and doing a new install on passenger side...