I have a 69 grande equiped with the old loosy-goosy steering. I'm interested in upgrading to a power rack and pinion setup. I know that there are many bolt-in kits available for this, but they all seem pretty pricey and furthermore, I would like to try my hand at fabricating one from a unit...

HAYNES FORD MUSTANG REPAIR / SHOP MANUAL 1964 1/2 thru 1973 V 8 Covers engines: 260 ,289, 302, 351, 390, 427, 428, and 429 cubic inch. Manual is in good condition with no pages missing or torn. Not greasy. Covers complete teardown and overhaul instructions. 288 pages. illustrated. Published 1979

OK, so I am trying to put on a serpentine belt and i am about 1/4" off from bieng able to get it onto the pulley... Is this normal? Do I just need someone with more muscle? I even removed the tensoner so it would not get in the way for the install. I tried using a screw driver and pushing it over...

Don't think the message went thru the first time. I've got a bunch of 2005 Saleen items for sale; Car was built into a drag car, these items are no longer needed. Front Sway Bar: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1,1&item=8071090695&sspagename=STRK%3AMESE%3AIT Coil...

Hi: I've got a 1965 Mustang - 289 2v carb - all rebuilt, but it's been sitting for many years - about 10, perhaps (withough starting or running at all). After cleaning the gunk from the carb and the gas tank, replacing the fuel pump, plugs, points, condenser, plug wires... I have a problem when...

Can any one tell me the difference between the console for a 66 convertible automatic with air and a coupe automatic with air? How long are they? Thanks

I've got a mach 1 under the dash wire harness I want to clean up. Is there a solution I can use to soak the harness?

Check out the new Car & Driver. The new Shelby GT500 ran a disappointing 12.9 @ 112 mph. Not really any faster than the previous 4.6 Terminator Cobra. (Hopefully we don't have another '99 Cobra fiasco happening.) The Corvette ran 12.8 @ 113 / 0-60 -- They also raced two low-milage examples of...

Just received this...... granted this publication is focused on investors, but we could sure use some good news.... Dear MoneyNews Reader, Saudi Arabia's oil minister Ali al-Naimi is warning that oil price hikes and global oil demand could soon disappear. In fact, he is also warning that oil...

Article with NoOp comments. --- DETROIT -- After debating Pontiac's viability this year, General Motors' leadership plans to revive the brand's heritage of performance with a product lineup of exclusively rear-wheel-drive cars. There would be no trucks and - after the next generation of vehicles...

I thought I knew how to replace brakes! 1972 mustang coupe Brakes were working not great, but they stopped the car. Replaced all wheel cylenders, masterbrake, shoes, drums (4 wheel drum, no power anything) and bled them. I get no air when bleeding, refilled the master 5 times (never letting it go...

Check out this note and the pics. With Dodge playing the crowds how far off can the Challenger be from production? Look out, Mustang! http://forums.focaljet.com/team-pit-stop/511945-fj-exclusive-one-off-dodge-challenger-rolls-cruise-night.html Patrick

I have a 2000 mustang 3.8 5 speed with 72,000 on it and it may be coming up on a clutch replacement. I have replaced clutches in older model vehicles but not a mustang. Is there anything I need to be on the look out for? Could I do it my self with out special tools? Any suggestions for type...

Anyone here use Pro3 lower control arms on a Fox Mustang?Pros/cons?

Is there a rev limiter on my 6-cylinder 2000 Mustang? When revving the engine, it seems to artificially stumble right around 4000 RPM, and won't rev any higher. Since redline is quite a bit higher (5000? I'm working from memory here) there seems to be some sort of a limiter at work. Assuming...

If one only needed to change one singe alxe, what would be the cheapest easiest procedure for swapping them? My son decided to steal my wifes car, slamming into something and shattering the rim, rotor, and bending the rim-mounting flange. I have ordered the correct axle but have never been inside...

I heard through the grapevine that your Mustang is gonna be a star - when?

Employees from DamilerChrysler supplier, Collins & Aikman told NewAgeMuscleCars.com today that they are working on engineering certain components for the upcoming production version of the Dodge Challenger. Even though Chrysler has said that the decision to build the Challenger will not be announed...

Ok the skinny is I have this Ford truck (more details below) that I am told (though I don't believe) that it has a 1972 Mustang 302 in it! So here are a few details in a list form: 1978 Ford F-100 2 wd pick with a 3 speed manual trans. 1972 302 V8 Mustang engine I want to drop the three speed for...

Does anyone have the Ford tire pressure spec for this tire size option on the '94-'95 Cobra? Thanks -- Richard '94 GT 'vert Under Drive Pulleys