|
|
Replacing Belts, Rounded bolt by
Steve W.
Fred wrote:
> Replacing PS belt on a 77 Dodge Van 318. The adjuster bolt head is
> partly rounded and having problems getting a grip to loosen it. I don't
> think even a closed end wrench will work.
>
> Any ideas on easiest way to remove it? I don't have air tools only hand
> tools. Vice grips...
|
|
6 |
523 |
|
|
|
|
0 |
475 |
|
|
How to remove center console 2003 alero by
jdagy
I'm looking for help in removing the center console on an alero - I
can't seem to get past removing the gear shift lever. - I need to
ge to the fan and air conditioning controls. Any simple hints?
|
|
2 |
713 |
|
|
|
August 11th 07 01:32 PM
by *
|
4 |
571 |
|
|
|
|
4 |
488 |
|
|
1997 GMC Suburban Door Panel & Brake Switch by
cover
I've got a '97 GMC Suburban that has some sort of issue with the
drivers inside door handle and it's ability to open the door (drivers
window must be rolled down and door opened with the exterior handle).
Autozone doesn't show instructions for a '97. Rather, if you choose a
'97 model, you get...
|
|
6 |
214 |
|
|
Ford pickup low voltage at idle by
Nate Nagel[_2_]
I think I posted about this before, but never really got beyond two
suggestions...
Problem is this. When truck is idling, if enough accessories are turned
on, voltage will start to drop, and keep on dropping as if the battery
is discharging. Voltage at battery with key off is about 12.9...
( 1 2 3)
|
|
23 |
872 |
|
|
Magic rear drum removal technique? (Cavalier) by
George[_10_]
('99 Cavalier, emergency brake doesn't hold (req'd for NYS inspection).
Backing up to stroke the adjuster doesn't seem to be going anywhere.)
The drums are really rusted (?) onto the hubs. The best method I've
found is to apply major heat and rap it with a hammer. Over and over
and over. Well,...
( 1 2)
|
|
14 |
995 |
|
|
DROSKOSKI by
ConservativeCapital.com
http://groups.google.com/group/cnbc-million-dollar-challenge/browse_thread/thread/fb886b489b302f29
http://www.myreader.co.uk/msg/129617490.aspx
http://myreader.co.uk/msg/129617442.aspx
http://www.finance-forums.co.uk/forum/viewtopic.php?id=3474
http://www.finance-forums.co.uk/forum/viewtopic.php...
|
|
0 |
380 |
|
|
Cam position sensor (CMP) removal? (Cavalier) by
George[_10_]
('99 Cavalier 2.2L)
I have an intermittent CEL, with a Cam Position Sensor DTC. I'd like to
at least check the connector, but I'm having trouble reaching it. It's
on the back side of the engine.
The Chevy book just says to remove the right wheel, and reach in. That
would work better for Mr....
|
|
0 |
244 |
|
|
Free advertise at new forum by
action841
Advertise for free at new forum.
Register in a second and promote your business for free:
http://www.fashion-forum.org
|
|
0 |
364 |
|
|
Repost on wheel bearings for Sebring by
[email protected]
I posted about a week ago in reference to my 2002 Chrysler Sebring. I
need some input again. A couple of months ago I noticed that when the
car was moving I hear a sort of humming sound coming from the front
end that gets louder as I go faster. I thought that since my tires
were old and fairly...
|
|
6 |
252 |
|
|
Bad Diode Stator means? by
sorry
Sorry to keep bugging everyone about this, but I just don't know.
77 dodge van 318. On startup ammeter needle swings from full
charge to midrange. Loud squealing when ammeter needle swings to full
charge. Noise goes away after engine warms up. I think I tried
tightening the belt long time ago and...
( 1 2 3)
|
|
25 |
1,052 |
|
|
|
August 10th 07 01:26 PM
by xjx588
|
0 |
773 |
|
|
auto inspections by state by
The Derfer[_2_]
Anyone here have a list of which states require automobile
inspections and which don't? Or is there a web site that has
such a tally (if so, couldn't find one).
Thanks in advance.
|
|
7 |
412 |
|
|
|
|
39 |
1,492 |
|
|
|
|
0 |
1,197 |
|
|
Invisible water!!!! by
Sameera
Invisible water!!!!
http://www.coolvids.info/tricks-movies/invisible-water/index.html
The movie shows a very innovative technique of invisible water...
enjoy!!!!
|
|
7 |
526 |
|
|
|
|
5 |
249 |
|
|
Lumina 2004 Won't start, stalled while driving by
rajanm99
I have a Lumina 2004, in november 2006, it stalled while driving, took
it to a workshop, they tested and changed egr sensor valve and
ignition module. Then it run for few thousand kms, car stalled
intermittently, then workshop checked and changed crack sensor. After
a month, the car stopped again...
|
|
3 |
209 |