Ive got a 69 coupe. Ive been thinking seriously about doing a drop kit to finish off the look of the car. I hope everyone knows what Im talking about when I say that on these cars , they appear to be higher in the front then in the back, because of fender flare or wheel well size or whatever....

Cant find anything usefull on fordracing.com these days. This kit comes without roller lifters, with 1.7" roller rockers. First off, just curious if it will give significant gains on the low end. Throttle response, torque, etc. Will the high lift be too much for a smooth running street...

NBC gave away a SE GT 500 KR KITT car, also a Focus and 2 other models. I couldnt watch the new knight rider last sunday for more than 5 min it looked so terrible. But I wouldnt mind winning that car. Id drive it a couple times, sell it to pay off my house, AND buy a new GT or Saleen and make a...

Ive always wanted a 5.0 mustang but Im sick of morons that wont sell them no matter how old and rusty for less than $5k. So ive decided to build my own. I know i will probly spend more than $5k in the long run but it wont be all at once and I can build the car exactly how I want it. So ill be...

Apparently these are unique to Ford, one of those inovative designs :). In the passenger side back corner of the engine bay theres a "brick" connector with 4 vacuum lines going to the air pump, the oil filler neck, the manifold, etc. One of them snapped like a twig. Im in the middle of a project so...

I was thinking about stroking my block to 393 or 408 as a winter project. And getting a kit with forged parts for more strength on the bottom. Id like to use my stock block but I was looking on coasthigh.com whos kits were recommended by people on stangnet. They say 69-70 block extra care must be...

Ive sent to summitracing but wont hear back till next week. Someone must know this. In the middle of a project, Ive got a BBK #1557 cold air kit sitting on the floor, because of situation change I need to upgrade my fuel injectors and MAF. The BBK site says this cold air kit wont fit aftermarket...

Is this possible? Only thing im worried about is the tranny kickdown. I had enough trouble just putting an edelbrock carb on it. Would I have to fab up a custom kickdown rod and linkage or do they make em?

Id like to find some mach 1 buckets or a high back seats with head rests that will bolt right into my 69 coupe. I keep an eye on ebay and have checked stangnet. Does anyone make reproductions of classic seats? anyone have any sites I can check? Thanks,

I posted this couple months ago but didnt get any replies. 89 GT 5spd. Just got subframes on yesterday, this summer, mini starter and high flow fuel pump are done. Ive got the Edelbrock performer top end on my 69 351W (cylinder heads, cam, intake) and really like it. But I havent seen a lot of...

returned a skin from a big mustang dealer ,was disappointed in the quality. looking for the best quality and fitting door skin, any recommendations on who sells this

I have a 72 mach 1 Mustang with no Motor are transmission . I am buying a junk yard 351c with C6 from a 1974 Cougar. I can't find a netural safety switch on the Cougar transmission. Where should the switch be on a 72 mustang C6 Tranny. Can this combination work?

Ok, my 89 Mustang's reverse lights for some reason are not working. I have replaced fuses and the 2 flasher fuses. All other lights work except the 4 Turning lights. But I know that the reason that does not work is in the switch in the steering colume. I know that because the Hazards all work...

Anyone have an OEM 03 Cobra hood that they are willing to part with? Also looking for an 01 or 03 front bumper cover. If you have any go fast parts for an 01 Stang hit me up as well. Fernando in Texas 2001 Oxford White GT

Car Ionic Air Purifiers with Ozone O3 These things sound good, has nayone tried them? I found them on EBay for under $10 http://stores.ebay.com/OneSmartMove Please share your experience if you have tried something similar .... Thanks in advance

Don't do any business with him or there. He has physically threatend a former member there... D3G Governator: i have these two friends i went to high school with that are now..... welll..... do odd jobs on the side D3G Governator: its not the kind of people anyone would want to **** with D3G...

how easy are they to replace, have one worn, can see how the top two come out ? Any help out there? Thanks in Advance

having a problem on where to start, what to do, I have the wiring diagram for my 66. not sure where to start at. 1. does my brake lights run through my turn signals? 2. Could my brake switch be diconnected from my dash? any help would be great, u can email me direct at

Does anyone have a current Carfax account? Im looking at this Mustang, 1FACP41M2PF173579, and would like to get some info on it. My email address is if someone could run a report for me. I appreciate it. Kevin

Guys, I have serveral problems going on with my 93 GT. like, front end sqeek, rotors and more. The questions are posted at: http://forum.howtofixyourstuff.com under automotive. Would appreciate any help you could offer. mustangdude