|
|
1988 Suburban TBI stalling and choking by
tpcolson
5.7L with TBI: I replaced the knock sensor and the cap/roter. It still
starts hard and stalls and chokes under acceleration. It won't even make
it up a hill unless at idle. Touching the gas pedal causes it to choke and
sputter. Any ideas? thanks.
|
|
1 |
939 |
|
|
1994 F-250 Computer Problems by
ford250-460
Looking for info on what to do about my truck. My '94 F250 has a 7.3L 460.
103k and a good clean engine with no oil leaks, generally a really good
truck. It began to run like crud so on the recommendation of my Mechanic
I replaced all of the EGR (4,metal ones off back of engine) did an
extensive...
|
|
0 |
723 |
|
|
'79 FJ40 Rear Differential rebuild by
Paul Hovnanian P.E.
I may be needing one soon. The pinion bearing had some play in it.
What's a reasonable price for a rebuild? I can pull the differential
carrier and bring it to the shop myself (saving the axle-pulling labor
charges).
What are the best shops in the Seattle area to have this done?
--
Paul...
|
|
3 |
866 |
|
|
Xterra Firma site dedicated to the Nissan Xterra Community by
Sitting Duck
Xterra Firma is the premiere Internet destination for all things related
to the Nissan Xterra SUV. This site is for the community and by the
community - sharing and kind-hearted discussion are very much
encouraged. Whether you off-road, compete in audio, crawl the malls or
you just love your...
|
|
1 |
1,044 |
|
|
Grand Cherokee 4WD problem by
Micah
Hello Folks,
I have a 2000 Gr. Cherokee that makes a noise which seems to speed up
as I accelorate; something like a branch caught in bicycle spokes.
It's always in 4WD and I do not have the option to change this. I have
a feeling it's in the Transfer Case but would hope that a Jeep with
52,000...
|
December 2nd 04 09:03 PM
by Micah
|
0 |
699 |
|
|
Steering pull by
Spud Demon
I have a problem on my S-10 Blazer 4x4. The steering pulls.
It pulls gently to the left when accellerating or cruising, then when I hit
the brakes it jerks to the right suddenly and then doesn't pull any more.
I have listened for noise from all this, and there isn't any that I can
tell.
Does...
|
December 2nd 04 12:10 PM
by Myron
|
3 |
665 |
|
|
91 Ford Explorer 4x4 by
damion
I own a 91 explorer i want to convert to full time four wheel drive . is
this a nightmare or what want to make a fun ride for my kid on our
property .
|
December 1st 04 09:02 PM
by Chris
|
7 |
1,364 |
|
|
'92 Land Cruiser Transmission Rattle by
Greg Neef
I have a rattle in what I think is the transmission on my 175K '92
Land Cruiser. It is most pronounced when in gear but not moving.
Anyone else had this or have ideas on cost to repair?
|
|
1 |
817 |
|
|
Chevy Blazer Broken/Stuck Bulb in Rear Right Tail Light by
Spiderman
The rear right (passenger side) brake light & turn signal were not working
on my 1989 Chevy S10 Blazer. When I went to replace the applicable 2057 bulb
(dual filiment) in the tail lamp, the old bulb just broke right
off....apparently it was corroded/stuck inside the socket. I tried to remove
the...
( 1 2)
|
November 30th 04 01:03 AM
by Franko
|
10 |
2,239 |
|
|
|
|
0 |
944 |
|
|
FS: 1948 Willys CJ-3A hunting jeep by
ken bonin
1948 Willys CJ-3A. Original engine. Four wheel drive train is operable.
Locking hubs. Roll bar and bikini top. Military tires including spare.
First $2,000. Runs good.
Great hunting jeep, not street licensed as is.
Reply e-mail if interested. Vehicle is in San Antonio, TX.
|
|
0 |
1,140 |
|
|
what is it? by
Wedge Motor
I have been driving by this military jeep for a while but I wasn't sure
what it was. Upon closer inspection, I noticed a manufacturer's tag on
the dashboard that was written in Italian. The vehicle was listed as a
Fiat 1101A. My question is does anyone know anything about these
vehicles and when...
|
|
2 |
558 |
|
|
|
|
1 |
734 |
|
|
Did I ruin my engine ??? by
Mike McAuley
'02 2500HD 4x4 with 6.0L gas engine.
Inadvertantly put in about 5 gallons of old, yellowed gas from another
vehicle that had been sitting idle for about a year. No doubt had water in
it too.
2 days later, the 2500HD wouldn't start in the morning and making very scary
($?) clanging noises. After...
|
|
4 |
942 |
|
|
possible to make a full size Chevy 4x2 work in sand? by
[email protected]
Is there anything I can do besides a 4x4 conversion that will make my
4x2 full size G20 van make it through some pretty thick/sinky sand?
My thought is to put a put a locker on the back, give it a lift, and
carry around some Mickey Thompson 35x17.5 tires which I can pop on only
when I need to make...
|
|
6 |
1,132 |
|
|
Kilby skid for TJ for sale on Ebay by
Marc Sebens
Like new Kilby skid on Ebay.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=7937737332&rd=1&sspagename=STRK%3AMESE%3AIT
|
|
0 |
819 |
|
|
Trip to Disney by
mickey
GET YOUR TRIP
TRIPS TO DESNEY
TRIPS TO HAWAII
http://travelexpert2004.us
http://travelexpert2004.biz
http://gotraveling85.us
|
November 28th 04 04:50 PM
by mickey
|
0 |
624 |
|
|
Knurling a piston ??????? by
John M. Wright
I just took my 300 block in to be tanked and bored. The guy at the machine
shop says that the block isnt worn enough to need boring. Just a hone and
piston knurling should be good enough. I've seen knurled valve guides, but
a knurled piston ?OK, thats a new one on me. Is this a good thing or...
|
|
3 |
1,154 |
|
|
Go Skydiving ?? by
Freefallu
or if you would like to jump in spain check out
www.freefalluniversity.co.uk
--
Freefallu
------------------------------------------------------------------------
Freefallu's Profile: http://www.landyzone.co.uk/lz/member.php?userid=342
View this thread:...
|
|
0 |
510 |
|
|
1994 Explorer hubs "grinding"/"buzzing"/"noisy" when disengaged by
Chris
Hey everyone,
When I bought my truck, the 4 wheel drive did not work (front wheels did not
have power). My mechanic observed that the right side worked, but the left
side did not.
I picked up a used hub at the wreckers, installed it, and the 4x4 now works
fine.
However...when i disengage the 4...
|
|
2 |
1,523 |