A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Post New Thread
Threads in Forum : Ford Mustang Forum Tools Search this Forum Feed Icon
  Thread / Thread Starter Reverse Sort Order Last Post Replies Views
Clutch installation by
I'm going to call around tomorrow to see how much putting in a new clutch will cost me... but I thought I'd post here first to see what some others have paid & what the average cost for INSTALLING is (not for parts + install, but just install). Thanks guys/gals. -Mike -- A happy kid behind the...
(Multi-page thread 1 2)
November 12th 04 10:13 PM
by Go to last post
12 641
$3000.00's FOR HORSES by
How many miles are on the car? What condition is the drivetrain in? If you've got $3,000 to blow.. I'd look into supercharging the car... maybe 6-9psi intercooled. It's a 302 & I know that blowers for 302's are generally less expensive than those for 281's.. check...
(Multi-page thread 1 2)
February 15th 05 10:47 PM
by Michael Johnson, PE Go to last post
13 2,802
PING: Patrick (NoOption5L) by
I have a few bucks handy & could use some bathroom reading material ;). Just kiddin, but really... which magazines do you think I would most benefit from.. and which are the most interesting? I've looked at MM&FF and 5.0 Mags... both interested me.. both had interesting articles... are there...
March 1st 05 03:46 AM
by Go to last post
2 197
Touchup on powdercoated wheels? by
Have the chance to pick up some powdercoated 18x10.5" wheels for pennies on the dollar ($600 total for a set of 4, with rubber). Only catch is, the guy scraped a curb, and theres a pea-sized chip in the powdercoat. Its not chipping around or anything, but it is silver (looks ugly, if you spot...
May 3rd 05 03:24 AM
by Go to last post
6 244
backfiring by
I have this problem that's been the plague of my '65 Stang for the last several months. Ever since a damn-near complete overhaul of the top-end (after a bout with piston slap) I've had this crazy repetitive clacking sound coming from the passenger-side lifters.. and particularly in the last few...
May 3rd 05 08:21 PM
by GEB Go to last post
3 282
Installing steeda clutch quadrant by
I've never installed a clutch quadrant before. I have an aftermarket aluminum clutch quadrant in now. Can anybody point me to documentation (pref. with pictures) as to removing & installing a new clutch quadrant? I've already removed the clutch cable (also Steeda). -Mike -- Melt away the...
May 4th 05 06:58 PM
by Brent P Go to last post
7 255
Finally, some pictures by
Some better than others. More coming soon, and ofcourse the ronaele install later this week. Anyway, www.hzdev.net
(Multi-page thread 1 2)
May 7th 05 05:13 AM
by John C. Go to last post
17 247
PING: Tim (Musttanguy) by
Ok, quadrant was a piece of cake to get installed. The cable... well.. diff story. When I removed the old clutch cable the first time, it was bolted onto a part... I don't know what that part one. Like, there was a metal bracket attached to the middle of the cable (not exactly the middle, but near...
May 4th 05 06:12 AM
by Go to last post
4 209
Help troubleshooting ECM code 96 by
Greetings! Looking for some advice on troubleshooting a code 96 on a 1989 Mustang GT 5.0 5-speed. Code 96 states that it is a fuel pump secondary circuit failure. the car seemingly runs fine, and I just cleared up some EGR issues code 33 by replacing egr sensoreand vacuum actuator. The engine...
August 10th 06 01:22 PM
by Go to last post
0 248
Cams again by
How much should the avg cost for installation of camshafts for my car be for labor? Thanks. -Mike -- A happy kid behind the wheel of a 98 Mustang GT Cold air intake
January 24th 05 07:07 PM
by Go to last post
2 185
neeed help with 73 coupe by
hey there I am wondering what to do with my wifes 73 coupe. I am redoing it for he and I noticed that the front end is rotted out under the main cross member under the motor. How hard would it be to replace the metal or should I try and find new one or just upgrade with costume front end with all...
January 21st 05 02:09 PM
by Scott Van Nest Go to last post
3 253
Yet another 2005 Mustang question by
I know that the discussion of 2005 Mustangs is getting very worn out & FAST, but I have a question for you guys... how long do you think they'll keep this body style? 94-98, 99-04, 05-??. -Mike -- A happy kid behind the wheel of a 98 Mustang GT Cold air intake FRPP 3.73 gears
November 15th 04 03:18 AM
by John Smith Go to last post
4 523
Pinging by
Car is pinging every new and then at full throttle... maybe 1/5 times. It's very unnerving. Also, I'm losing about a 1/4 of a quart of oil every 3k miles. I'm going to clean the air filter today, clean sensors, I already replaced EGR valve. What else would you recommend I do? Thanks in...
(Multi-page thread 1 2 3)
November 15th 04 08:58 PM
by Go to last post
20 1,003
302 V8 upgrade on six w/ auto tranny 1969 Mustang by
I just bought a 69 coupe with the 250 inline six w/ auto tranny. I have a 302 lined up and ready to be transplanted, this should be a straight deal right? Or are there going to be major implications. I also plan to put in a manual trans a little later, any recommendations? Also will the 302...
November 17th 04 08:54 PM
by David E Willson Go to last post
3 417
Plug wires by
Anybody know where I can get some plug wires for my 98 GT for a decent price? I've checked eBay for Ford Racing 9mm wires... $90 buy it now + $8 shipping. Seems a tad high to me. -Mike -- A happy kid behind the wheel of a 98 Mustang GT Cold air intake FRPP 3.73 gears
December 11th 04 12:59 AM
by SVTKate Go to last post
5 272
Considering 02 coupe by
Depends on how much abuse the car has seen. Generally they've been reliable to most ppl that I know... mine has been reliable USUALLY.. but it has caused me some grief (but the car you're looking at is also 4 years newer than mine..). I'd say check it out extremely thoroughly... see how...
December 13th 04 12:12 AM
by Martin Go to last post
6 353
Error codes finally. by
Check engine light JUST came on... so I immediately pulled out the code reader & got: 0307: Cylinder 7 Misfire Detected 0174: System too lean (Bank 2) Car stumbles/hesitates when accelerating... idles fairly rough. Any ideas?? Thanks in advance! -Mike
(Multi-page thread 1 2)
January 8th 05 07:14 PM
by Go to last post
19 287
1995 Mustang by
Look for a digital clock that's mounted on the dash of my 1995 mustang. Can anyone help. --
January 8th 05 01:39 AM
by SVTKate Go to last post
4 244
PING: Tim (Musttanguy) by
Check email please =). I need to change my order. -Mike -- A happy kid behind the wheel of a 98 Mustang GT Cold air intake FRPP 3.73 gears Steeda Tri-Ax Shifter Flowmaster 40 Series mufflers (self-installed woohoo)
January 8th 05 03:18 AM
by Go to last post
3 273
Help on troubleshooting ECM Code 96 by
Greetings! Looking for some advice on troubleshooting a code 96 on a 1989 Mustang GT 5.0 5-speed. Code 96 states that it is a fuel pump secondary circuit failure. the car seemingly runs fine ,except it does not seem to have as much power as it should. I just cleared up some EGR issues code 33...
September 29th 06 06:51 PM
by KEITH MCCUMBER Go to last post
1 285
Post New Thread


Display Options
Showing threads 1 to 20 of 6210
Sorted By Sort Order
From The
Forum Tools Search this Forum
Search this Forum :

Advanced Search

New posts New posts More than 15 replies or 150 views Hot thread with new posts
No new posts No new posts More than 15 replies or 150 views Hot thread with no new posts
Closed Thread Thread is closed  
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 10:37 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright 2004-2019 AutoBanter.
The comments are property of their posters.