|
|
86 2.3 Electrical/Charging system questions by
[email protected]
Hi;
My 97 cobra is parked and my 86 2.3 LX winter beater is out!
Background;
With headlights, turn signal and heater/rear defrost on, the rate at
which the turn signal flashes goes down significantly than when there
are no accessories running. My assumption is that the electrical system
is not...
|
December 26th 04 12:48 AM
by Rein
|
6 |
663 |
|
|
86 2.3 mustang camshaft alignment problem. by
CCTGENE
The timing belt broke on my son's 86 2.3 Mustang. The timing pointer that
you align the timing mark on the camshaft sprocket with is missing. Is there
any other thing that I can use to align the mark with? Hoping there is away
of doing this without having to removing the valve cover to actually see...
|
|
1 |
377 |
|
|
86 GT 5.0 Idle Question by
LR
I have a 1986 Mustang GT 5.0 with the five speed manual trans. After warm
up and when idling, the engine idle speed "surges" (ie. it varies up and
down, slightly, but noticeably).
Anyone had any experience with this, what is the matter and what I might do
to correct it?
Thanks a bunch.
Larry
|
|
4 |
494 |
|
|
86 GT Resurrection by
python1
I have a stock 5-spd 86 GT. The tranny blew in late '03 and the car has
been sitting until present.
I got this car for my 18th birthday (I'm 30 now) and was a daily driver
until the tranny failure. I have a sentimental attachment to it. My
plan is to getting it running again, and then routinely...
|
|
0 |
182 |
|
|
86 mustang With t-topos by
[email protected]
Hello I have an 86 Mustang Gt with T-tops ,the window doesn't go up
tight when you roll it up ,(they are power )The weather stripping is
new.
Is there a place to adjust the window so it fits snug to the t-top.The
gap is about a quarter inch
thank you
|
|
0 |
281 |
|
|
87 COUPE, RECIPE FOR 7.76 1/8 mile 1.56 60 ft. by
Winze
one complete 87 4 cyl. LX coupe $400.00
add junkyard 87-92 5.0 H.O engine
used X303 cam
shaved & minor home ported E7 heads,factory valves
crane single valve spring kit, no machining
pro products, typhoon intake
650 DP holley
duraspark distributor, GM 4 pin module,4 cyl ford efi coil
1.6 bolt down...
|
October 20th 06 06:16 AM
by Winze
|
2 |
307 |
|
|
87 GT convert top not working by
[email protected]
I am trying to get my roof working Ive replaced the pump,lines,&
cylinders all I get is a click in the relays.There is power to the
line to the pump.No info available on convertibles.Any help is
appreciated
|
|
4 |
529 |
|
|
87 mustang by
Gregory Oldham
I just recently rebuild the enginf in a friends 87 GT conv.He wanted/had to
change to mass air from speed density.So,instead of waiting for me to
help,he decided to try it himself.Now he is the problem.I have 6 or 8 wires
hanging out of the ecm harness connector and no idea where the "H"...
|
|
2 |
416 |
|
|
87 mustang 5.0 family member? by
[email protected]
I need to bounce something off of you guys!!! I saw an old friend the
other day, who I hadn"t saw in a long time. He still had his old 87 5.0
that he had bought new. After a feew beeers and some old war stories I
asked for the keys??? He gave me the keys, and I proceeded to do a
doughnut, a...
|
|
5 |
546 |
|
|
87 Mustang 5.0 Stalls when Hot by
gantone1
When hot my 87 Mustang 5.0 will buck and stall. Normally it will
'restart' before engine dies completely. WHen this occurs the tach
drops to 0 RPM even though the engine is still turning (but with no
power). Because the tach drops so fast my guess is that the problem is
ignition or electric...
|
|
3 |
322 |
|
|
87 mustang convert still not working by
[email protected]
i've got a new pump ,good lines and cylinders,13 to 14volts at the
plug for the pump,and when i try the switch all i still get is the
click from the resistors.any suggestions would be appreciated cause i
have no ideas left
|
|
5 |
502 |
|
|
87 mustang GT front brake upgrade question by
John Hale
When replacing the front brakes with 73 mm calipers (91 Lincoln Mark VII),
do you need to get different
(bigger, the ones used for a 91 Lincoln Mark VII) size rotors or will the
same ones do that are on the car. I realize that you should get slotted
rotors. Will the stock rotors on the 87 Mustang...
|
|
5 |
854 |
|
|
87 Mustang GT help.... by
DBZVegetaIII
I have had my 87 Mustang GT now for a few months, but for some reason,
like most 'Stang owners do, I feel the need for more speed. I am not
very knowledgeable about these things, as I have never tried to fix a
car up before. I was just wondering if someone could give me some
advice on what mods I...
|
|
5 |
405 |
|
|
87 Mustang GT tail lights by
[email protected]
I am looking for a pair of bright red GT tail lights(not the LX ones).
I would like them in near perfect to perfect condition(or new if
possible).
I am fixing up a mustang and both of the ligths are broken so I really
need them. I bought a pair of blue tail lights with the intention to
paint them,...
|
|
6 |
651 |
|
|
87 to 67 distributor by
jeffgrever
my name is jeff. i restored a 67 mustang with a 289/30 over. i want put a
87 5.0 electronic distributor in place of the old points distributor. how
do i accomplish this?
i would
appreicate the intel thanks jeff
|
February 17th 06 03:33 AM
by Mark C.
|
6 |
645 |
|
|
87-90 interior door handle stuck by
Hollywood
On two of my fox body mustangs I have unfortunatley encountered
(somehow at the same time...;sigh;) the driver's side interior door
handle failure. I have had the actuator / and/or rod inside the
door-mechanism come apart; although in this case the interior handles
gave way and are now sticking out...
|
|
1 |
384 |
|
|
87-93 carbine fiber Mach I hood by
Nicholas Anthony
Does anyone know were I might find a carbon fiber Mach I hood that fits the
'87-93 Mustang GT's? I know its pretty rare in the first place to find a
carbon hood let alone if they even make a Mach I style. Greatly appreciate
the help, thanks!
Nick
|
|
0 |
281 |
|
|
87-93 door lock question by
Randy Pavatte
Hello everyone.
The power door lock doesn't work on the passenger side of my 90 GT, and
I suspect the actuator has failed.
I've researched this item online, and there's a huge difference between
the OEM Ford part (appr. $140) and a reproduction (appr. $60).
Should I expect any difference in the...
|
|
4 |
796 |
|
|
87-93 LED tail lights by
mrsask
Hi
Anyone have some good recommendations for 87-93 LED tail lights??
Thanks in advance.
T
|
|
2 |
309 |
|
|
87-93 shorty or long headers? by
'87-STANG-IN-S.A.
whats the difference between shorty and long headers? and if so which
one puts out better performance and sound?
|
|
3 |
521 |