|
|
67 Mustang Coupe. $20,000 painted your choice of color. Or as a project car. by
Dan
I have been working on a 67 Mustang Coupe project. I replaced all the
rusty floor pans, frame rails, battery tray area, trunk areas and inner
cowl panel. The outside sheet metal is excellent. I had the car sand
blasted and it has self etching primer on it. The interior floor pans
and entire under...
|
May 10th 06 09:23 PM
by Dan
|
0 |
423 |
|
|
Fog Light Harness Location by
officer
I have a 02 mustang 3.8 and am wondering where the fog light harness is
located under the hood. It is attached to the switch console inside but I
have yet to find where it goes under the hood . Any help would be
appreciated! Thanks!!! Guy
|
|
3 |
353 |
|
|
Power Steering hoses...loose? by
JohnO
Poking around under the hood of my kid's 79, I noticed what looks like
a loose hose. One of the lines between the poweer steering pump and the
swtiches to a hard line, which moves
freely as if it isn't fully tightened. Unfortunately, I can't figure
out how to get a wrench in there to see if the...
|
|
3 |
474 |
|
|
'66 broken motor mount by
vbrink
I had the driver's side motor mount repaired on my daughter's '66
mustang. Within 30 days the motor mount broke (the original passenger
side mount didn't break). When mount broke, the engine torqued, ruined
the brand new radiator, and the new paint job on the hood.
After the new motor mount was...
|
|
9 |
555 |
|
|
Midolyne by
JohnnyK
Has anyone used this? I want to buy from Laurel Mountain as they seem to
have by far the lowest prices, but they use midolyne instead of
polyurethane.. Anyone tried this stuff? I don't really want to be
replacing bushings because I don't like them in a year or two..
Also, how are their suspension...
|
|
0 |
336 |
|
|
help with speedo removal by
DM
I am trying to take my cluster out of a 1981 Mustang but cannot get the
speedo cable off it. There is a white plastic piece on the back that I dont
want to break. Cna anyone tell me what to do?
Thanks
David.
|
|
7 |
281 |
|
|
ATTN: Anyone in Austin, Texas by
Thomas Cameron
Hey All -
Do any of you go to the Saturday night car meet at Home Depot in Cedar
Park?
I'm (hopefully) about a month away from completing the 68 coupe with the
1994 Lightning motor. I want to take it out and I was wondering if anyone
else from this NG would be there.
Thomas
|
May 9th 06 03:12 AM
by Mike
|
1 |
255 |
|
|
The "500" In GT500 means 500 Horsepower by
[email protected]
2007 FORD SHELBY GT500 OFFICIALY RATED AT 500 HORSEPOWER
Ford Shelby GT500 officially rated at 500 horsepower, 25 horsepower
higher than preliminary estimates. The Shelby GT500 will go on sale
this summer with more horsepower than any previous factory-built
Mustang.
(DEARBORN, MI)...
( 1 2 3)
|
May 8th 06 12:34 PM
by Ritz
|
21 |
1,670 |
|
|
Convertible top on 93 mustang by
Lori
Hate to sound stupid but I am needing guidance on how to replace
cylinder the the top to work. Where does the hydraulic fluid go so I
can fill it? Does the top have to be up or down? Where do I start?
|
May 7th 06 11:48 PM
by Lori
|
0 |
382 |
|
|
|
May 7th 06 02:44 PM
by Paul
|
12 |
1,010 |
|
|
|
May 7th 06 12:43 AM
by KdF
|
1 |
450 |
|
|
1970 Mach 1 Rocker Panel Covers by
Jim
I am looking for a set of Rocker Panel Covers for a 1970 Mach 1.
I have looked everywhere that I know of and have not found any reproduction
sets.
I have found a few here and there on ebay, but not a complete set.
Does anyone know of any company or manufacturer that is making these ?
Or has anyone...
|
|
3 |
695 |
|
|
|
|
25 |
1,290 |
|
|
'66 speedo question by
Mark C.
I need to remove the speedo needle on my '66 to install a white face
applique. Any know how to do it properly?
--
Mark
--
|
|
2 |
354 |
|
|
WTF? Pinging 351W by
Blue Mesteno
My 400cid 351 Windsor stroker is only running 9.2:1CR but it's pinging like
crazy on the 85 octane here in Colorado. I've checked the gaps on my plugs
and the points, retarded my timing so far back it's probably -4 initial
(timing light doesn't go below 0). It STILL pings!!!! WTF!!!
I topped off...
|
May 6th 06 04:19 AM
by .boB
|
9 |
534 |
|
|
1995 Audio Replacement by
[email protected]
Hello, I'm trying to replace the sound system in my 1995 Mustang. Can
anyone give me any tips/links/advice? I need all the tips I can get,
ranging from head unit removal, to wiring diagrams, etc. etc. etc.
THANKS IN ADVANCE!!!
|
|
1 |
402 |
|
|
Looking for a piece (used, cut, whatever) of 1967 wheelwell by
JohnnyK
I need a piece (preferably the whole way around) of a 1967-68 (I don't
know what other years fit?) outwheel well, passenger side.. DOesn't have
to be the whole wheel well, about 2" from the surface where it meets the
quarter panel and up would be fine.. Also doesn't have to be the whole
thing, I'll...
|
|
0 |
437 |
|
|
87 mustang convert still not working by
[email protected]
i've got a new pump ,good lines and cylinders,13 to 14volts at the
plug for the pump,and when i try the switch all i still get is the
click from the resistors.any suggestions would be appreciated cause i
have no ideas left
|
|
5 |
502 |
|
|
Hemmings Mustang Tech and Price Guide Publication shuts down by
Spike
The Hemmings Mustang Tech and Price Guide has officially shut
down. I received my refund yesterday for the balance of issues I will
not receive.
Along with the notice and refund is an ad for back issues. There is a
lot of very good classic Mustang information in these issues. The ad
lists the...
|
May 3rd 06 08:42 PM
by Spike
|
0 |
408 |
|
|
|
May 3rd 06 06:46 PM
by DM
|
0 |
381 |