jeffcoslacker Wrote: > Sounds like you have a tooth or two broken off the regulator...I think > it's plastic on yours. Easy enough to replace, though... http://www.speedyautoparts.com/images/products_large/M462904.JPG] It's not the style I was thinking of, have to replace the whole assembly, I...

I have had a problem with the driver's window in my 1994 Mitsubishi Galant for the past year. The window stops half way down when either going down or up. It makes a grinding sound but if I apply some pressure it will continue going down or when going up if I pull it it will continue to close...

It's a 91 2.5L TBI ... the rig became progressively sluggish until it would hardly move. Any throttle movement would stall the engine. And the exhaust manifold was red hot before I chose not to drive it! Towed it home ... checked for a leaking TBI - NO CHANGE. Dropped the exhaust pipe - NO...

1993 Toyota Corolla (lost manual years ago) Both directionals stopped working today. Checked the 7.5,15 and 20 fuses and all seem to be working. Any ideas? Thanks.

Hello. My brake rotors on my civic keep warping. I had my front brake pads and callipers replaced. About a year later, they warped again, and the dealer resurfaced teh rotors. It's now about a year later, and they have warped again. I only drive about 5000 miles per year. What could be...

Does anyone know the physical location of the EATX Relay in the 91 Plymouth Voyager 3.3L? The trans intermitantly goes into limp-in and I want to try changing this relay before replacing TCM. Thank you for your help.Ron

Okay here's the problem. Initially the starter would not stop cranking after the ignition off after trying to start. Replaced the ignition switch, still did it anyway. Replaced wires: ground cables, starter cable from solenoid, and the solenoid itself. Fixed the starter problem, we thought. ...

I am very inexperienced with transmissions and hope that someone has an idea on where to start with a problem we're having with the transmission in my father's 1965 Coronet. It has the original '65 727 transmission and a 440 engine. The only mods known to the transmission are a high stall converter...

Was wondering if anyone knew where the low pressure service port was for the A/C sys. on a '99 Olds Aurora? Before I start removing wheels and fender well spash shields. I flat can't find it under the hood, and it's not shown anywhere in the factory serv. manual or on Alldata that I can find. ...

I don't know if this is planed this way, but to me it looks like this guy is destroying his Jeep. They call it "Total Jeep Burn Out", but it almost looks like Jeep Burn Up : http://www.jumpingpixels.com/jeep.html

O.K. I have new info on my problem. I decided to power brake it when i got home tonight. I just slowly increased the R.P.M.s Sure enough right at 1600 it started to miss, then went away at 1800. No miss above or below that range. It sounds like it is just one cylinder, not multipull misses. ...

I have a 2000 Mitsubishi Eclipse GT with a V6 engine. About a month and a half ago, my radiator cracked at the top so I changed it for a new one. As I did and started up my car to take it home, I noticed that the water in the radiator reserve tank was being sucked into the engine very quickly. The...

Sorry, I never said what engine was in the van. Its a 3.8 . The plugs did look very white when i replaced them. My thoughts are the throdle position sensor. Maby a little weak spot right in the common cruising position. Thanks, TP

I'm having problem with the ac on my 1998 ford explorer cycling on/off at weird intervals. My first thought was that it had leaked and was low, but after buying a gauge it was found to be in the middle range of "full". Sometimes it will cut on when I first get in the car and may run for an hour...

Looking for a place to connect the vacuum gauge line/hose for manfold vacuum. Have an Auto Meter Vacuum Gauge for under the dash. Can't seem to find anything that resembles a rubber vacuum hose for tapping into, on this engine. 2005 Buick 3800 V6. Harryface 05 Park Avenue 41,698

How much does an automobile depreciate from a mechanic's wear and tear during a repair job? Belt buckle scratches due to not using fender covers, soiled tires from greasy hands, grease on the upholstery / floor mat / doors from greasy hands. scratched / damage interior molding. damaged / broken...

I went and got replacement seatbelt motors that go up inside the doors, from a salvage and got a really good deal. Now the problem is I have no clue how to install them & don't want to pay out the butt now to get them in. If I had instructions, I know i could pretty much do it myself, but am...

Is there anyway I could get the valve timing diagram for a standard CFR engine running on gasoline? Will these valve timing values change if a different fuel is used?

THE BIG OIL COMPANIES DON'T WANT YOU TO KNOW ABOUT THIS: AMAZING "" Breakthrough Product "" !!!!!!!!!!!! YOUR GOVERNMENT EPA HAS TESTED THIS!!!!!!!!!!! EPA CERTIFIED TEST RESULTS!!!!!!!!!!!