Did VW ever make self adjusting rear breaks for a type 1 ? Thanks Mark

Tshirts books and posters with artwork by Peter Schwanden (the idiot book illustrator) http://www.peteraschwanden.com/index.html

http://youtube.com/watch?v=18Bpy4EvivI

Recently started having this problem with my Bay 1600cc. It is very hesitant at low revs, and even if I put my foot down or pump the throttle a bit too get some fuel in there, it still takes a little while to pick up. Once the revs pick up it pulls strongly. It needed a service anyway so I...

You know, 2006 is near, the nuclear war with Iran is only a few months ahead. After that, the Earth will be a desert, radioactive and most parts uninhabitable. So how can I modify my VW so that I can still use it in the desert world of tomorrow ? You know, some Mad Max "The Road Warrior" -...

Hi... I'm new to the group and wanted to first say "Hi". I have been a long-time bug owner (for about 20 years) with miscellaneous bug over those years. Most recently a '71 standard bug. My last one was a '58 that I had to get rid of because I moved and it just wasn't going to work out. (Wish I...

I have a 1967 Type I Beetle with a stock diaphragm clutch. The clutch cable breaks every couple of years. It always breaks at one of the ends where the cable is crimped into the fitting. It never breaks anywhere in between. I always grease the cable upon installation. Is this common to break this...

On 5/18/2011 9:20 PM, Joey Tribiani wrote: > How are ya buddy? Still kickin'. Thanks for the thought. :) I still keep my finger in the VW pie, but haven't had the time to stay on RAMVA.

I ran across this in someone's signature on Samba: "1960 VW bug/pickup conversion (junk)" I sent him a message asking if he had pics of it. He sent me a few and I offered a trade of a tacked together rolling sand rail chassis for it, Today, after 276 miles and 3/4 tank of diesel, the Baja...

I replaced my starter with a 'new' rebuilt one... When I turn the ignition, there's a grinding noise momentarily and then it starts. I removed it to check the flywheel gears and the starter gear look fine, no shavings. Is it possible the starter is bad? What else should I check? tia,

I'm looking to take my 72 rear diagonal arm off. With the tranny out, the frame is almost bare so taking this piece off gives me a good chance to get rid of all the rust and re-paint it all. That 17" allen bolt is to be "peened" according to Bentley.. What does this mean, exactly? I noticed it has...

THAT **** SHE SAYS I HAVE TO SELL IT, CAN YOU BELEIVE THAT!!!! ANYWAY IT HAS HAD A GROUND UP RESTORATION AND NO RUST WITH ONLY 10 MILES ON THE NEW ENGINE. I AM WILLING TO SELL IT FOR $5 - I LIVE IN ****ING FINLAND

Alldata 2004, , , Mitchell CDs, year 2005 - 2003 , 53 CDs, total 107 CDs ----------------------------------------------------------------------------------------------------- Alldata 2004, , ARRIVED IN BETWEEN 31/MAY/2004 to 28/JUNE/2004 FULLY FUNCTIONAL, AND GOOD FOR UNLIMITED SEATS.

I have changed everything on this car. Master cylinder, metal lines, rubber hoses, wheel cylinders and still have the same problem that I started with the pedal goes to the floor if I pump quikly they will get tight I can even move back alittle on the pedal and push forward and it will hold but...

Jeff 1974 vw bug looking for the bottom engine bolts to pull the motor. ARE THEY on to of the engine tin that protects the valves connected to the heater boxes? lots of oil and junk leaking from the old tubes for 120,000 miles

We have advantage on providing than other providers for handbags andshoes the brand like // and mo 1) we are the professional replica factory provider and seller, we get products directly from the manufacturers, we cooperated for more than 6 years, so we can get the latest new replica styles at...

I have a 1979 Type 2 bus that has been laid upm for 7 years. The valves had been set with a gap. In then correcting the hydralic setting to 2 extra turns there was then no compression since the valves were now not seating. How does one cure this problem? Wioll the hydraulic sleeves leak away...

my 74 type one will not start i turn the key and NOTHING no click nothing battery is good any suggestions on where to look? jerry

http://good-times.webshots.com/album/560088269FDkEKd?start=192 The engine was rebuilt first and enjoyed while waiting its turn to look as good as it runs. Mario

I am looking for a shop that builds sand rails and is located in the Southeast since I live in Asheville NC. Does anyone know if such places are around these parts? Thanks, Scott..