Hello, The car was in storage and won't start. I detect no spark and have cleaned all electrical plug connections with cleaner spray. Anyone have advice on what to check first, and how - for example ECC, All components look clean from crank position sensor to modules.

Just wondering about the feasability of placing a Diesel engine in a 71 Ford Mustang. I've always liked the 71 Fastbacks, and with the added bonus of them having one of the largest engine bays, I assume that this swap is possible. Of course this would be for a biodiesel project, and perhaps...

Bosch Turbo Bypass Valve For Audi Porsche VW SAAB Bosch Turbo Bypass Valve For Audi Porsche VW Watch a VIDEO of it here http://www.metacafe.com/watch/496175/bosch_turbo_bypass_valve_for_aud... Buy It here http://stores.ebay.com/OneSmartMove

Very Cool Autocross video, same corner, different cars, Porsche, S2000, Prelude Very Cool Autocross video, same corner, different cars, Porsche, S2000, Prelude http://www.metacafe.com/watch/499248/autocross_collection_different_cars_same_corner/

Any of you guys have spec info on 67 Mustangs? I am attempting with little luck to search facts about how many 67's were made with Diamond Blue (N) code produced?? My 3rd 67......but don't recall this color very often or at ALL.

I am the proud owner of an 05 GT convertible. I recently noticed a couple of different 05s that have sequential turn signals. I noticed that my 05 does not have sequential turn signals. Is there an aftermarket kit to add this or was this an option I missed?

1964½ is a term that is used by Mustang owners and enthusiasts to describe the earliest Mustangs ever built. Although Ford never officially used the term "64 and a half" to describe these cars, they did arrive on the market in early 1964, before other true 1965 models. The first Mustang actually...

Its not a Mustang,but... If anyone knows where I can get a drivers door for a 2 door 76 Granada,please email me direct as soon as possible. Its gotta be straight and bondo free. Sorry to post a non Mustang topic,but I cannot locate one anywhere. Any help is appreciated. Thanks-D

Since it's sunny and warm out I decided to take my headlight switch out and to give it a good spraying of contact head cleaner or possibly replace it. From what I've been told the knob is taken off by pushing in a clip. I've found the clip but no matter how hard I push I can't get the knob off...

Ok i just bought a 98 dodge caravan se from a private seller the passenger side window goes down if I use the controls on the driver side door but you can still put up the window using the passenger side control? what is wrong with it am i going to have to replace the motor in the window or is it...

http://www.jcil.blogspot.com << The Greatest News Ever!

HI all, Hoping I can get a little help here. I have a 73 Bronco rebuilt 302 and C4 with about 2000 miles on both. Got in it yesterday and noticed my kid probably had moved the transfer case shifter. I moved it back to 2wd backed out of the garage. When I put trans into park there was slight...

I have to rechrome my floor mounted gear shift shaft for a 4 speed transmission - I can see how to disassemble the shifter from the trans and the leather knob from the shaft - but how can you remove the rubber boot from he shaft since the "T" pull handle is in the way. It looks like that...

Any performance recommendations for a set of headers for a 1968 302 V8? Can't be much larger vertically than stock or much longer than stock as I will have some clearance issues in this project application. Should have good lateral clearance. Concerned that much of the stuff on the market does...

I have a 1968 Mustang 302 V8 power train in a 'Ford Exotic'. Four barrel carb and 4 speed. Can someone provide me with the following factory recommendations: Timing in degrees BTDC at idle (625 rpm) and fully advanced? Thanks to all respondents, Ron Patterson

I am transplanting a 1968 302 V8 into a project car. There is not enough clearance to pivot the stock Ford alternator. Can someone help me with wiring in the Nippon Denso alternator I just purchased. It fits in perfectly. It has the large screw terminal that I know goes to the battery or...

Hi guys! I've got a 69 mustang coupe I've had for several years now, that's a daily driver. The engine has finally gotten to the point where I can't bear to see my baby like that, so I pulled the engine a few days ago with the help of my brother, a chevy guy. Anyways, I'm not looking for a race...

Somebody help me out here... I'm trying to replace the parking pedal assembly on my '69 (the old one has pieces missing), and I've got it unbolted from the kick panel area, and also have the two clips that hold the cable in place off... but I can't figure out how to get the cable pulled out...

Does anyone have access to a flat rate manual? I want to put cross drilled rotors on the front of my mustang. 2006 GT Coupe, I got a quote of 4 1/2 hours. This seems a high quote to me. Just a labor quote. Thanks, Ron

My son just informed me his car is due to be inspected before month end and his horn doesn't work. He's also managed to lose his owners manual AND the cover from his fuse box. Does anyone have a diagram of a fuse box layout for a 90 Mustang LX 5.0 they could email me? Or can someone tell me...