While setting the parking brake the handle came off in my hand. The end of the cable broke at the handle. I bought an OEM cable but am unsure of how big of a job it is to re-route thru the car back to the rear brake yoke. Any knowledge to share about this task?

Sorry for the double posting. My lame-ass ISP didn't record the message on the server I view it on, so I re-posted, but Google picked it up both times- Thanx for the info. I don't want to remove the body so I better hope they clean and pressure test well-Lib

My original roller-latch door was replaced with a chrome generic. Does the early door use a special bezel to accomodate the roller on the door? Are the door, hinge, and bezel (if necessary) the only parts I need to make this swap? Thanx- lib

What would be the recommended grease/lube for the wheel bearing and u-joints on a 1963 small block 4spd? I'm replacing all of the above. Thanx- lib

Is there a way to lube the headlight motor bearings? It has been garaged for over 20 years and I don't want to damage them when opening for first time. I know they have a manual knob and they both worked correctly when put away. Any tips before rolling up? Thanx- lib

They have been dormant for over 20 years and am getting close to energizing electrical system after re-build of most of car. They both worked well when I put car in storage.Can these motors be lubed without being dis-assembled? Any recommendations before putting power to these motors? Thanx- lib

I have replaced or rebuilt the entire brake system (all shoes- no discs or power)on my 1963 SB. I am going to run a silicone fluid in the system when I charge it up. Any recommendations on brands of fluid to use or stay away from? Thanx- lib

I see this vehicle listed on Ebay- http://cgi.ebay.com/ebaymotors/Chevrolet-Corvette-STINGRAY-1963-SLIPT-WINDOW-CORVETTE-STINGRAY-RED-with-AUTO-TRANS_W0QQitemZ200120764748QQihZ010QQcategoryZ6168QQrdZ1QQcmdZViewItem- and in the seller's description he say's- "A third extra tail light from 63...

I removed my O/S LH mirror today and discovered that the mount appears to be from a 63L to 67E, according to catalogs. Would it be possible that the screws that hold the mirror mount to the body would match up with the screw spacing on the 63E long-base kit. I can't tell by looking in the...

The car was stored for 22 years. Should I replace the brake metal brake lines when I replace the metal fuel lines. Does brake fluid degrade and leave deposits in the lines (as gasoline can)? As there are no visible cracks, holes, etc. in the lines could I just blow them out w/comp. air when they...

I had the car stored for 22 years. Should I replace the brake metal brake lines when I replace the metal fuel lines. Does brake fluid degrade and leave deposits in the lines (as gasoline can)? As there are no visible cracks, holes, etc. in the lines could I just blow them out w/comp. air when they...

I need to by many mechanical parts (clutch assmbly, brake shoes+lines, carb. kit, hoses, etc.) for my car that's been garaged for apporx. 22 yrs. I'm having the work done by a mechanic friend who has a garage near where the car is (Washington state). I live 2 states away but want to buy the parts...

I have a 1963 w/327 (250 hp?) approx. 96K miles that I'm getting back on road. What is the current wisdom on dealing with unleaded gas in this motor? I may have to pull the heads for other work after 20 year sit. Thanx- Lib

Is there a particular lot that is available (non-handicapped), or one that I can pay to park in, that would cut down on the length of our walking distance to the reserved seating on pit side. Thanx- Lib

I am having the original hood for my roadster repaired (after 20+yrs.) and am considering either selling the replacement hood or storing it. The hood is painted and has been stored in a garage under a car cover. It has no chips or flaws. Any ideas about how to determine the value of the hood...

Has anyone experienced any differences (other than appearence) between a bonded lining and a riveted lining as far as stopping power, wear, noise, etc?

I have spent numerous hours gathering parts prices and availability on-line. I just ordered front+rear suspension re-build kits from Wilcox's and am going to order brakes, clutch, gas lines, etc. next. I have narrowed it down to 3 overall suppliers( Corv. Central, Eckers, and Zip) I haven't heard...

What is a good glass-pack muffler that is being produced today? I'm looking for one that is well made and has a bit of rumble under power and a crackle under back pressure. I'm lot looking for a loud, straight-pipe type, even though I'm sure they breathe better and give better performance, etc....

I want to replace all of the rear end bushings+bearings while I have the entire assembly out of the car. I had replaced the large bearing in the pass. side trail arm years ago after it failed and it was a major job, as I did it while trail arm was still on the car. I believe that is what...

I am taking my 63 SB in for service on Mon. I am trying to deal with the ongoing smoke out of tailpipes under acceleration when leaving a standing start, with 1500 mi. on complete re-bore and re-build. Per the machine shops analysis that this is un-burnt fuel, and not un-seated rings, I am...