On Dec 30 2007, 4:19 pm, wrote: I hope you remember the story. (If not, you can refresh your memory below.) You will NOT believe what the cause of the problem was! You know those two little screws that attach the ignition module to the distributor, they take a Torx wrench to ...

Just installed a new C4 in my 65FB and while trying to align the shifter (oem full console) I found that the shift control assembly is worn out and needs to be replaced. Though maybe someone might have one from doing a conversion from auto to manual.... or have leads on where one might be...

What's the future hold for our S197 platformed Mustang? Exterior design changes: Muscular-looking shoulder hump just aft of the door openings -- Said to resemble that worn by the Dodge Charger, but more of a flowing line Front and rear fascias get a tune-up -- taillights are messaged a bit

Porsche 997 Carrera S - 05 blackmet., leather, 19" Carrera classic alloys, cruise, nav, clima, sunroof, parking assist, fullpower options, financing available, exceptionally nice Porsche roadster at dealership in Sweden. Phone: +46 (0) 705474830

NBC gave away a SE GT 500 KR KITT car, also a Focus and 2 other models. I couldnt watch the new knight rider last sunday for more than 5 min it looked so terrible. But I wouldnt mind winning that car. Id drive it a couple times, sell it to pay off my house, AND buy a new GT or Saleen and make a...

I'm in the process of replacing the oil pan on a 1991 Ford LTD (5.0 Liter Engine). Any suggestions on the best way to do this. Anything I should watchout for specifically? The Haynes book says the oil pan can be removed & replaced without pulling the engine by jacking the engine up at the oil...

Could you please see if the theft lamp is on or off while it cranks? Al

Could someone tell me a good tool to use to cut the old door hinge pins of a 1989 Mustang LX? I have a pair of "bolt cutters" but the nose is not long enough to fit between the door and the fender. It is a rolling restoration. Thanks, Ty Addison ---- Posted via Pronews.com - Premium...

I am in the middle of replacing my exhaust from the cats back on my 93 'stang. When removing the old parts, I did not pay any attention to the distance from the tailpipe to the tire and now that I am installing the new parts, it looks like one of the tailpipes is too darn close to one of the...

So Im trying to decide. Edelbrock is $1700 but doesnt include EFI intake. Trick Flow is $2400 and is the winner cause they include push rods, EFI intake AND roller rockers! BUT they dont include the roller lifters for the roller cam. Is that because its ok to reuse stock roller lifters with the new...

Taken from Hemmings Motor News Holley declares bankruptcy After 100 plus years in business, Holley has announced it is seeking protection from creditors by declaring bankruptcy. While this does not mean that the company is going out of business, it does mean that Holley has to reorganize and pay...

I would like to know if anyone has experience with the K&N 63 series aircharger system on a Mustang GT. Is the reported 15 hp boost there? More importantly, has anyone had challenges with their Ford warranty as a result of installing this item? Thanks!

world peace harmonious extreme is good! Chinese antique (1912-1949) Republic of China porcelain teapot 528 chinawares 400 please watch¡£ world Only pure variety the antique chinaware series big collection has the very big collection value and the development good opportunity!!! Website...

Funny, no one did ANYTHING until the protectionist EuroTRASH complained. The U.S. has complained about this for DECADES. China suffers first defeat at WTO Chinese car plant Foreign-made car parts are in a less favourable position, says the WTO China has had its first defeat at the World Trade...

My 03 started right up today. Ran for about 10 seconds and died. Had no tools or time but I unscrewed the plastic cap on the Schrader valve on the fuel rail. No fuel pressure. Here is my question. Does the passive alarm disable the pump? Never paid attention before, but when I was trying to...

Patient: 1993 Cobra/125,000 miles -- stock except: shorty headers, advanced timing, 73mm C&L mass-air meter and an A9L processor. This combo ran solid for a number of years and the symptoms suddenly -- no mods or changes were made -- just appeared. The symptoms have gone on now for about 1 1/2...

1997 Ford Mustang, V6, 3.8L - Car has lost power and engine is running rougher. - Autozone diagnosed that cylinder 2 wasn't firing. - Removed #2 spark plug wire from ignition module, held close to module and no spark. - Swapped #2 & #6 wires and #2 wire was okay. - Cleaned and regapped #2 spark...

I know Super Tuesday has yet to arrive, but after the bru-ha-ha down here, it looks like it'll be McCain and Clinton. What say you?

I am considering a pre-emptive intake manifold replacement on my wife's 1997 G.M. 54,000 miles, looks and runs like new. I checked Advance Auto Parts website and found two choices, the Motormite at $265, and the Dorman at $199. The show a picture of the Dorman, and it appears to be all plastic...

what type of damage can be cause from grinding gears? -- Message posted using http://www.talkaboutautos.com/group/rec.autos.makers.ford.mustang/ More information at http://www.talkaboutautos.com/faq.html