|
|
1979 Tach not accurate by
[email protected]
Hi Guys,
My 79 has a tachometer issue. The RPM's seem to be anywhere from
1500-2000 off. Recently my warehouse got flooded. The vette was in
the warehouse and the water (fresh water)got up to just above the door
pulls. Thankfully the dashboard wasn't under water. I am currently
replacing all...
|
|
0 |
326 |
|
|
C4 Vibration by
Alex
My 94 convertable starts to vibrate around 65 mph.
Feels like it is in the back of the car. Can feel it through the gear
shift, so could it be drive shaft? Car is just at 100K.
Recently acquired the car, first vette, so no history on the car and not
sure where to start looking.
Is this a...
( 1 2)
|
|
11 |
1,512 |
|
|
Install O/S mirror on 63 early? by
lib
I see that the correct mirror ( longbase)is specific to my 63E. Does the
interior door panel need to be removed to install a mirror correctly or is
it done externally? The driver side has been replaced with a generic
mirror.I am considering replacing it and doing a new install on passenger
side...
( 1 2)
|
September 20th 07 03:31 AM
by lib
|
11 |
606 |
|
|
1990 Vert by
gjt
Hey group:
Bought a 1990 vert. 1st vette. I have had it about two months and never
put the top up. Did so today, its in pretty bad shape. I went to put it
down, now I cannot get it down. The supplemental top instructions are long
gone. I know the back has to come forward to clear the back...
|
September 20th 07 02:18 AM
by gjt
|
0 |
328 |
|
|
|
September 19th 07 02:37 PM
by joevett
|
1 |
499 |
|
|
|
|
0 |
491 |
|
|
|
September 18th 07 02:47 PM
by Ed
|
0 |
384 |
|
|
63E Mirror mount specs? by
lib
I removed my O/S LH mirror today and discovered that the mount appears to be
from a 63L to 67E, according to catalogs. Would it be possible that the
screws that hold the mirror mount to the body would match up with the screw
spacing on the 63E long-base kit. I can't tell by looking in the...
|
September 18th 07 04:16 AM
by lib
|
2 |
348 |
|
|
NOS Speedo cluster by
rhino[_2_]
NOS speedo and tach cluster for '78 - '82 corvette complete with
bezel/lens $175
|
|
0 |
264 |
|
|
FS: 1972 Corvette stationwagon by
Eugene Blanchard
A buddy of mine has a few C3 Corvettes for sale including a 72 Vette Wagon.
Here's the site:
http://www.rickscollectables.com/catalog/index.php?cPath=21_23
--
Eugene Blanchard
http://www.cadvision.com/blanchas
Home of the DIY Hot Rod Kustom website
|
|
4 |
417 |
|
|
1979 Cam replacement by
[email protected]
I have a pretty clean 79 L82 vette that Id like to put a performance
cam in... question do I need to take out the motor or is there
enough room to take out the cam without removing the motor? Also
any suggestions on the type of cam? I want something that gives
decent performance but is...
|
|
3 |
324 |
|
|
84 HEI Tach drive distributator by
Art[_3_]
This may sound like a real foolish question, I had a Mallory HEI
distributator installed last year. My vete left me sit along the road, it
just stopped running. From the tach connection on th edistributator there
are 2 wires, one was taped (the insulation was stripped off) and I am
wondering if...
|
|
0 |
283 |
|
|
Brake lights/backup lights not working ? by
slovetteman
87 Corvette....118K miles...
I'm having a problem with brake lights and backup lights not working.
I've checked the obvious --- bulbs, fuses, etc., and now at a loss as
to what could cause this problem.
Could this be a switch problem? Although I'm not aware of any switch
that would control these...
|
September 14th 07 11:35 PM
by PJ
|
5 |
523 |
|
|
C3 seat questions for the group by
[email protected]
Hi
I'm looking to purchase both seats for my '74. When I bought the car
it had some aftermarket seats in it (anyone interested in these?). I
would like to get back close to the originals. I have a few questions
for anyone who might care to answer. Provided I have the right
mounting hardware what...
|
|
3 |
389 |
|
|
|
|
0 |
410 |
|
|
American Collectors Insurance by
87Blue
Hello,
I'm going to get agreed value insurance for my car and am looking at the
American Collectors company. Has anyone ever filed a claim with them and how
did it go? Any other suggestions along these lines of agreed value policies?
Best,
Bart
--
( 1 2)
|
September 13th 07 12:45 AM
by 87Blue
|
12 |
1,150 |
|
|
Can any of you number nazis... by
±© Flipper Mike ®³
Can any of you number nazis...tell me what these two intakes are from.
Thanks in advance.
1. casting # 3794129
2. casting # 3731398
|
|
1 |
489 |
|
|
|
|
11 |
879 |
|
|
Header temps ; before and after coating with Jet Hot by
Dave in Lake Villa
Had the 1970 BB Hooker Super Comp. Headers Jet Hot coated at their
Mississippi plant ; elected to go with the 1300 f. Sterling Coating .
I have a Lazer Thermometer and after a good long run, i measured 532 f.
(at idle) right where the Header pipes meet the Cylinder Head , before
sending them to...
|
|
5 |
469 |
|
|
|
|
8 |
339 |