|
|
GT Ford Mustang by
marlimon
My driveway goes over a ditch and when i was leaving I drove the front
right tire off the driveway...the bottom of the front end was then stuck
on the driveway....i managed to back up out of it but scraped the bottom
of the car really bad...now when i turn right the car makes a deep
squeaking...
|
July 28th 05 08:23 PM
by RichA
|
2 |
271 |
|
|
|
July 28th 05 08:40 AM
by RichA
|
0 |
716 |
|
|
More transmission questions by
Thomas Cameron
OK, so I found out that the Lightning engine that I am putting into my 68
coupe was mated up to an E4OD transmission, not an AOD. So I am wondering
- since it seems like it is going to be a nightmare to get the
Lightning's computer to work correctly without the tranny it is expecting
to talk to, I...
( 1 2)
|
July 28th 05 06:03 AM
by Spike
|
10 |
1,306 |
|
|
94 Mustang electrical problem by
audeogod
My stepdaughter bought a used 94 Ford Mustang Convertible with the V-6
engine recently. The car came with a Pioneer CD player that someone else
had installed. For a few months the car seemed to run and do fine. But
for the last month or so, the car has developed electrical problems that
seem...
|
|
0 |
368 |
|
|
|
July 28th 05 01:02 AM
by Gill
|
1 |
621 |
|
|
Brake caliper rebuild question. by
Mark C.
I'm rebuilding the stock ft calipers in my '69. What's a good lubricant to
use on the seals that's compatible with brake fluid or should I just use
brake fluid itself? It's not a good lubricant.
--
Mark
--
"I was thinking of the immortal words of Socrates who once said, "I drank
what?". " Val...
|
|
3 |
688 |
|
|
Power steering with 1994 EFI 351W engine in 68 coupe? by
Thomas Cameron
Like I mentioned a few weeks ago, I am putting a 1994 EFI 351W engine from
an SVT Lightning into my '68 coupe. The '68 has power steering, and I'd
like to keep it. The engine pulled from the Lightning has a PS pump
attached. Does anyone know how hard it would be to make it work with the
'68's...
|
|
3 |
535 |
|
|
66 Mustang Antique Bronze paint mixture required.... by
Nicole
Hi there guys just wondering if anyone can help me , I need the paint
mixture for a 66 Mustang Antique Bronze. as here In Australia No One can
help me ...... :-(
Also would like to know who was the paint manufacterer back then.
Or anything that might be of help.
Thx In Advance
Nicole
|
July 27th 05 08:58 PM
by DDB
|
2 |
622 |
|
|
04 Mustang Fuel Filter replacement by
rickster
Is there a special tool needed to remove the fuel filter on the '04 model?
I replaced the same on a '96 mustang with little effort a few years back.
Thanks.
|
July 27th 05 03:26 PM
by Kruse
|
1 |
607 |
|
|
|
|
5 |
739 |
|
|
How do you remove the 5th gear synchro hub from a '95 T-5 by
[email protected]
I'm trying to remove the 5th gear from the cluster shaft on a '95 T-5.
I am stuck on the synchronizer hub. It won't come off.
I drove the pin out of the 5th gear shifter fork, and I also removed
the external C-clip from the end of the cluster shaft. This allowed me
to remove, in order, (1) an...
|
|
4 |
764 |
|
|
air intake kit by
Abbas
I'm thinking of buying air intake system for my mustang gt 95. I was
looking at eBay and price ranges were from $60 to $200+.
What could be the differences in these sets? Or what is a good system?
Thanks
Abbas
( 1 2)
|
|
10 |
1,077 |
|
|
Raising the rev limiter setting on a '94 w/ AOD-E by
Richard
Is anyone aware of an inexpensive way to raise the rev limiter settings on a
'94GT w/AOD-E?
--
Richard
'94 GT 'vert
Under Drive Pulleys
Transgo HD2 Reprogramming Kit
High Stall Torque Converter
|
|
0 |
512 |
|
|
'69 brake rotor question. by
Mark C.
I'm installing a set of new, quality stock replacement rotors on my '69
mach. What is the best way to keep the "rough" areas from turning rust
brown? I'm not sure if caliper paint rated at 900' will hold up, especially
in the cooling fins area. Plating or buying a plated set of rotors is not...
|
|
1 |
662 |
|
|
Is there a programers for a 1997/2000 Mustang by
Dan
Hypertech has a Power Programmer for 1997.
Diablo's Predator goes back to 1998 but you could call and check to
make sure there is no PCM version overlap. The SCT Xcalibrator handles
PCMs back to 1996 but the original version doesn't allow end user
customization. You have to have their tuning...
|
|
2 |
622 |
|
|
|
|
10 |
1,539 |
|
|
89 mustang hesitation by
toytrd89
I have a 89 GT with a 93 cobra motor which was recently rebuilt to a 308
with forged internals. The heads were redone with 202 in. and 195 ex. It
has a 70mm throttle body and egr spacer, gt 40 intake, 24lb injectors, nos
fogger system"not used at the moment", msd billet dist, 6AL, and HVC
blaster...
|
|
4 |
466 |
|
|
Question on wiring of 97 A/C pressure switch by
[email protected]
A few weeks ago I posted a problem with a family members 97 V6 A/C not
working. A poster suggested removing the A/C pressure switch and
hitting it a few times because sometimes it can get stuck. Well I tried
that and it did not work, but I noticed that on the switch there are 2
electrical pins, but...
|
|
5 |
922 |
|
|
67 mustang gas tank pressure by
Linda in Iowa
Recently got a 67 fastback and discovered a lot of pressure builds up in the
gas tank. It is bad even when the tank is only a quarter full. one day gas
was running out the gas cap when it was parked uphill. Is there a fix to
vent the pressure problem? Linda
|
July 26th 05 09:48 PM
by Hairy
|
1 |
433 |
|
|
Anyone work for Ford? by
Chad
I'm looking for someone who works for Ford that may be able to answer
some questions for me about the A/X plans and a current Ford vehicle
purchase. Different dealers tell me different things. Please remove
"remove" from my email address.
Thanks
Chad
69 Mach 1
|
July 26th 05 03:00 AM
by Chad
|
8 |
852 |