I need to replace the handle but there is a metal piece behind the set screw. Does anyone know how to remove this? Thanks, Mike

I need to remove the speedo needle on my '66 to install a white face applique. Any know how to do it properly? -- Mark --

Well, I decided it was time to upgrade my ’66 Coupe. Nothing fancy, no blowers or NOS (yet). Anyway, every old car like this needs better suspension, brakes, and steering before adding more power. This is a daily driver street car, and certainly not a race car. I also didn’t want to spend...

I'm hoping someone can shed some light on this and let me know if this is factory or if someone in the past has done some modifications to the flywheel and torque converter on my 1967 Mustang 200ci t4. I took notice that the ring gear has been spot welded to the torque converter instead of being...

Hi all, my 67 started running poorly all the sudden last week. It has 96K on it, replaced cap, rotor, plugs, wires last year. Still has points (I know this is on my list...). Had the Autolite 2100 carb rebuilt last year. Still seems to run rich, but generally runs well. I had read some info...

About a month ago, my '67 Mustang convertible decided not to start anymore. First thing that happened... when I turned the key to start her up, the starter solenoid went "pop" in a flash of light and a bit of smoke. I figured the solenoid was fried, and got a new one. Turned the key and got the...

All new hardware, including master cylinder and the fronts were upgraded to disc. The only thing that hasn't been replaced is that directional valve 'thingy' which, I'm guessing, acts as a failsafe. Have bled the brakes numerous times, however, the pedal keeps travelling to the floor. Is that...

I have to rechrome my floor mounted gear shift shaft for a 4 speed transmission - I can see how to disassemble the shifter from the trans and the leather knob from the shaft - but how can you remove the rubber boot from he shaft since the "T" pull handle is in the way. It looks like that...

I decided to add new watershields(dust shields) to the doors while doing other work on them. The repro shields I have are brown paper on one side and slick black on the other side. Should the slick black side go inside or show outside(toward the interior)?

I'm installing a set of new, quality stock replacement rotors on my '69 mach. What is the best way to keep the "rough" areas from turning rust brown? I'm not sure if caliper paint rated at 900' will hold up, especially in the cooling fins area. Plating or buying a plated set of rotors is not...

See it at: http://houston.craigslist.org/car/584547697.html http://buzztrader.com/cars/1/01/7/19691017459.html -- John - ThunderSnake #59 '69 Mach 1 w/ 390 4V Wide Ratio Toploader

Hi folks, I just bought what I was told is a '69 Mach 1. I haven't located a body buck tag for it yet and I think the door sticker has been painted over. Are ther any other definate ways identifying it as a MACH? It has the deluxe interior, cobra jet hood scoop with hood pins, fold down rear seat,...

I just installed the moulding around the grill on my '69. It's made by a company called corvex and its pure crap. Nothing fits right. Is it supposed to be aluminum or stainless steel? Is this the only company that makes trim for early mustangs or is there a better company out there? -- Mark -- "I...

I can't tell how to install these suckers. I can see the holes in the door where the screws go, but I can't figure out which way the "L" gasket faces or which surface the screws go through to hold it on. Anybody know? -- Scott W. '66 HCS Mustang 289 '68 Ranchero 500 302 '69 Mustang Sportsroof...

i ordered a new tank for my 1966 mustang. the company i ordered from(sacramento mustang) sent me a tank for 1969. the 69 tank is a 20 gal. and the 66 is a 16 gal. the parts from my '66 don't sync-up with the taller tank. any suggestions?

I'm looking for OEM snorkel with working flapper, S-tube, and heat shield with brackets.

Hi Folks, I just bought a nice clean '70 sportsroof with no engine or transmission. I've got a built up 351W I could install in it but I was tossing around the idea of installing a 460 block. Will this fit and do you know of any companies that make headers for it? How about a manual transmission...

I found a 1970 Cougar carcass with a tach dash. I took the tach and have jerry-rigged it to my '70 Mustang's instrument cluster. Looks good with the white face overlay. I've grounded the back of the tach to the car's chassis and have run one of the two leads to my ignition switch for power and the...

I recently pulled my motor apart for a what I believe is its first rebuild. While taking the motor apart I noticed something that seemed odd. the camshaft sprocket has a plastic type substance that was between the teeth. It looks like the plastic was molded to the metal sprocket. Was this...

I just saw the '67 from a few posts ago with the 17 inch wheels. I don't think it looks too bad. What would it take to put a set of those GT wheels on my '71? Do you have to use a spacer to move the wheel out past the upper control arm? Saleen is advertising a set for $374.